clamping

英 [ˈklæmpɪŋ]

美 [ˈklæmpɪŋ]

v.  (用夹具)夹紧，夹住，固定; 紧紧抓住; 紧夹住; 被抓住; 被夹紧; 用夹锁锁住(车)
clamp的现在分词

现在分词：clamping　

计算机

BNC.43220 / COCA.42307

柯林斯词典

• 夹子;夹具;夹钳
  Aclampis a device that holds two things firmly together.
• VERB (用夹具)夹紧，夹住，固定
  When youclampone thingtoanother, you fasten the two things together with a clamp.
  1. Somebody forgot to bring along the U-bolts to clamp the microphones to the pole.
     有人忘了带把麦克风固定在支架上的U形螺栓。
• VERB 将…固定(在某处)；紧紧抓住
  Toclampsomething in a particular place means to put it or hold it there firmly and tightly.
  1. Simon finished dialing and clamped the phone to his ear...
     西蒙拨完号，把听筒贴在耳边。
  2. He clamped his lips together...
     他紧闭双唇。
  3. You beg him to try just one spoonful, and he clamps his mouth shut...
     你求他就尝一匙，可他就是不张嘴。
  4. Peter jumped to his feet with his hand clamped to his neck.
     彼得一只手捂着脖子，腾地跳了起来。
• (将违章停放的车辆扣在原地的)夹钳，车轮固定夹
  Aclampis a large metal device which is fitted to the wheel of an illegally parked car or other vehicle in order to prevent it from being driven away. The driver has to pay to have the clamp removed.

in AM, use 美国英语用 Denver boot


• VERB 给(车辆)上夹钳
  Toclampa car means to fit a clamp to one of its wheels so that it cannot be driven away.
  1. Courts in Scotland have ruled it illegal to clamp a car parked on private ground and then to demand a fine.
     苏格兰法院裁定，将停在私人地界上的车辆上夹钳并索要罚款的行为是违法的。

in AM, use 美国英语用 boot

双语例句

• Hydraulic hob mandrel clamping.
  液压滚心轴夹紧。
• The principle and its requirements of angle dividing and clamping equipment for bolted sphere nodes are put forward.
  提出螺栓节点球分度夹紧装置原理及要求，介绍了分度、夹紧控制系统。
• The key of processing tenuous hole by plain lathe is the design of clamping apparatus.
  用普通车床加工细长孔，夹具和钻具的设计是关键。
• In this paper, an effective solution-flexible clamping is introduced for grinding this kind of part.
  文中介绍了该类零件加工中一种行之有效的解决方案&柔性装夹。
• Analysis of Positioning and Clamping for Workpiece in Machining Center
  工件在加工中心上的定位与夹紧分析
• And tube clamps clamping, then check with soap and water before use without leakage.
  并用管夹夹紧，然后用肥皂水检查确认无漏气方可使用。
• In jig design most important link is the clamping and the detent mechanism.
  夹具设计中最重要的部分就是夹紧和定位机构。
• The structure of the shearing die, running on common use press, with radial clamping for round bar was introduced.
  介绍了一种用在通用冲床上的径向夹紧圆钢剪切模的结构、工作原理和设计制造要点。
• Relay IC3 opens, protecting the amplifier and clamping diodes.
  继电器IC3断开，保护放大器和钳位二极管。
• Sealed bearing system reduces clamping pressure and increases bearing life.
  密封的轴承系统减少夹持力并增加轴承寿命。