desquamate

英

美

v.  剥落，脱落，脱皮

现在分词：desquamating　过去式：desquamated　第三人称单数：desquamates　过去分词：desquamated　

英英释义

verb

• peel off in scales
  1. dry skin desquamates
  Synonym:peel off

双语例句

• There are some quality common faults in dwelling house engineering, such as sugaring, desquamate, empty and tympanic, and crack, which can seriously affect the impressions and usage effect of dwelling house.
  在住宅工程中，水泥砂浆地面起砂、脱皮、空鼓、裂缝等现象大量存在，严重影响住宅的观感和使用效果被视为质量通病。
• As a result, with water solubility cooling fluid the high frequency alternating heat stress is heavy, the coat desquamate quickly, the wear performance of TiN coat cutter is bad, so it is not adapt to the requirement of machining.
  结果表明，在水溶性冷却液浇注冷却条件下，高频交变热应力较大。涂层剥落较快，TiN涂层刀具的耐磨性较差，不能适应切削加工的要求。
• No bubble, wrinkle or desquamate.
  不起泡，不起皱褶或者脱层。
• The phenomena and mechanism of desquamate are defined for the first time.
  首次提出了竹材切削过程表面剥落现象及机理。
• On the condition of SRV wear, The predomination wear mechanisms of the products translate gradually from oxidation and abrasive wears to adhesion and desquamate with the increase of doped ZrC content.
  在微动磨损条件下，随着掺杂ZrC数量的增加，合成产物的主要磨损机制由粘着磨损、剥层磨损、氧化磨损和磨粒磨损逐渐转化为以剥层磨损和粘着磨损为主。
• Results showed the type of ceramic layer's wears failure was affected by ceramic layer's thickness under this friction condition; while the ceramic layer would desquamate if its thickness was less than the critical numerical value.
  结果显示：在滚动摩擦条件下，陶瓷层失效形式受到其厚度的影响，当陶瓷层厚度小于临界厚度时，试样表面出现陶瓷层剥落现象。
• Edge Detection for Chest Hydrocele Desquamate Cell Based on Combining of Canny Algorithm and Morphology
  基于Canny算子与数学形态学结合法对胸水脱落细胞边缘的提取
• There were the desquamate symptoms in the back of new-born rats in suramin and s+ r groups and the opisthotonos in suramin and s+ r groups with different degrees.
  suramin组和suramin+raFGF组幼鼠背部有皮屑现象，出现不同程度的角弓反张症状。
• The desquamate disappears with the increase of the moisture content but spiny hair appears on the surface if the moisture content is too high.
  随着含水率的增加，表面剥落现象消失，但含水率过高，切削表面出现拉毛现象。
• But under the dry condition the high frequency alternating heat stress is light, the coat desquamate slowly though a great deal little chap units is formed, the wearing performance of the TiN coat cutter is very good, the steady cutting time is long.
  与此相反，干式切削时，高频交变热应力较小，虽在涂层表面有微裂纹产生，但涂层不易剥落，刀具耐磨性较好，可进行长时间稳定切削。